TYPE:
CATALOG NO.:
General Description
The CCL/TCL Series provides functional emer-
gency lighting in a variety of wattages up to 450
watts. High performance electronics and rugged
18 gauge steel construction ensure long-term life
safety reliability.
CCL/TCL Series
High Capacity Steel Emergency Lighting Units
6 and 12 Volt, 75 to 450 Watts
Wet Cell Lead Calcium Battery
Illumination
Illumination is accomplished with up to three
lamp heads mounted on the top of the unit. The
most popular lamp head for use with the CCL/TCL
Series is the “D” Series round sealed beam Par 36
tungsten lamp head. The “D” head is available up
to 30 watts.
Housing
Constructed of 18 gauge steel with a tan epoxy powder
coat finish.
Knockouts provided for mounting up to three lamp
heads.
Bi-color LED charge monitor/indicator and a “press-to
test” switch are located on the front of the cabinet.
Dimensions
CCL75, CCL100, CCL150, CCL225,
TCL150, TCL200
Choice of wedge base, sealed beam tungsten, or halogen
lamp heads
Shown: CCL150DL2
Electronics
Battery
Low maintenance, free electrolyte, wet cell, lead
calcium battery
6.0”
120/277 VAC dual voltage input with surge-protected,
solid-state circuitry provides for a reliable charging
system.
(15.2 cm)
Charging system is complete with low voltage
disconnect, AC lockout, brownout protection,
AC indicator lamp and test switch.
Specific gravity disk indicators show relative state
charge at a glance
12.0”
(30.5 cm)
Operating temperature range of battery is 65°F
(19°C) to 85°F (30°C)
Includes two fused output circuits.
16.0”
7.6”
(40.6 cm)
(19.3 cm)
Utilizes a fully automatic voltage regulated two-rate cur-
rent limited solid-state charger -- initially provides a high
rate charge upon restoration of AC power, and provides
trickle charge to maintain batteries at full capacity once
float voltage is attained.
Battery supplies 90 minutes of emergency power
TCL300, TCL450
Code Compliance
UL 924 listed
6.0”
(15.2 cm)
NFPA 101
Optional ACCU-TEST Self Diagnostics includes an auto-
matic 3 minute discharge test every 30 days. A manual
test is available from 1 to 90 minutes.
NEC BOCA and OSHA illumination standard
12.0”
Performance
(30.5 cm)
Input power requirements
120 VAC - 0.66 amps, 80 watts
277 VAC - 0.30 amps, 80 watts
Warranty
Three year full electronics warranty
27.0”
7.6”
(12.7 cm)
One year full plus four year prorated battery warranty
(19.3 cm)
Ordering Information
CCL
150
DL
2
TD1
SERIES
DC
WATTAGE
6 Volt
75 = 75 Watts
100 = 100 Watts
150 = 150 Watts
225 = 225 Watts
LAMP
HEADS
# OF
HEADS
3 = Three
2 = Two
1 = One
FACTORY INSTALLED
OPTIONS 1
ACCESSORIES
CCL = 6 Volt
TCL = 12 Volt
6 Volt
A = Ammeter 2
DY = 8 Watt, Tungsten
DA = 18 Watt, Tungsten
DL = 25 Watt, Tungsten
DC = 30 Watt, Tungsten
ACF1 = 120 VAC Fuse
ACF2 = 277 VAC Fuse
LMSHELF = Mounting Shelf 300-450W
MXSHELF = Mounting Shelf 72-200W
ACP1 = 120 VAC Power Switch
ACP2 = 277 VAC Power Switch
AD = ACCU-TEST Self-Diagnostics
ADAL = ACCU-TEST with Alarm
ADTD = ACCU-TEST with Time Delay 3
DCP = DC Power Switch
12 Volt (Includes standard voltmeter) 12 Volt
150 = 150 Watt
200 = 200 Watt
300 = 300 Watt
450 = 450 Watt
DNY = 12 Watt, Tungsten
DE = 28 Watt, Tungsten
DK = 25 Watt, Tungsten
DG = 30 Watt, Tungsten
EX = Special Input Transformer (Specify voltage and frequency)
3
TD1 = 120 VAC Time Delay
TTD2 = 277 VAC Time Delay 3
(Suggested lamp heads listed
V = Voltmeter 2
above. Refer to the Accessories Section for
additional lamp head choices.)
W = White Housing
Notes:
1) Some option combinations may impact UL list-
ing. consult factory for specifics.
2) Not available witj AD, ADAL, or ADTD options.
3) 15 minute delay.
C1063R4
9/02 IH
5秒后页面跳转
STM32F030C6芯片介绍：主要参数分析、引脚配置说明、功耗及封装
PCF8591数据手册解读：参数、引脚说明
一文带你了解ss8050参数、引脚配置、应用指南
深入解析AD7606高性能多通道模数转换器：资料手册参数分析
微信公众号
抖音公众号
浙公网安备 33010502006866号 浙ICP备10014259号-119
营业执照ICP证
数据手册
如果您发现信息不准确，
