F
E
D
C
B
A
Technical specification:
At all times water resistant connectors not in use should be covered
with a Conec water resistant cap or water tight hood./
Im nicht gesteckten Zustand müssen die wasserdichten Steckverbinder
mit einer wasserdichten Conec Kappe oder Haube geschützt werden.
Technische Daten:
Working voltage/
Betriebsspannung:
100 VDC
5 A
Current rating/
Strombelastbarkeit:
Ω
Solder Instruction/
Lötanweisung:
Insulation resistance/
Isolationswiderstand:
> 1 G
D
D
1. Cable should be prepared for soldering. The cable / wires must be pretinned.
1. Litze zum Löten vorbereiten. Die Litzen müssen vorverzinnt werden.
2. Insert cable/ wire into solder cup.
Dielectric withstanding
voltage/
Spannungsfestigkeit:
424 VDC
2. Litze in Lötkelch einführen.
Solder cup accepts cable/ AWG 20
Lötkelch geeignet für Kabel:
3. Operate the soldering iron at 350 °C, 50 Watt max. and use a pencil tip.
3. Lötkolben Temperatur auf 350 °C, max. 50 Watt, einstellen.
Verwenden Sie eine entsprechendend Lötspitze.
Degree of protection/
Schutzart:
IEC 60529
IP67, in mated condition/
IP67, im gesteckten Zustand
4. Apply some solder to the solder tip to the soldering iron.
4. Bringen Sie etwas Lot auf die Lötspitze des Lötkolbens.
5. Put tip to wire in solder cup.
Temperature range/
Temperaturbereich:
- 40 °C ... + 105 °C
5. Setzen Sie die Lötspitze auf die Litze im Lötkelch.
6. After 1 second bring in solder.
6. Fügen Sie nach 1 Sekunde etwas Lot hinzu.
Capacitance value/
Kapazitätswert:
see table/
siehe Tabelle
7. Heat for 3 seconds longer. Do not heat contact more than 4 seconds in total.
7. Heizen Sie für 3 Sekunden. Erhitzen Sie nicht mehr als 4 Sekunden insgesamt.
8. Remove soldering iron.
8. Entfernen Sie den Lötkolben vom Lötkelch.
9. Wait until solder gets rigid again.
9. Warten Sie bis das Lot wieder fest wird.
Mating cycles/
Steckzyklen:
Quality class 3 = 50
Gütestufe 3
Quality class 1 = 500
Gütestufe 1
10. Do not solder adjacent contacts consecutively,
alternate position within the connector to minimize heat build up.
10. Um Wärmeentwicklung zu verhindern, sollte kein benachbarter Kontakt aufeinanderfolgend
gelötet werden, sondern eine andere Position im Steckverbinder.
Materials/
Werkstoffe:
Contact/
Kontakt:
Cu alloy, Au over Ni
Insulator/
High temp. PA GF UL 94 V-0
GD-Zn, Ni
Isolierkörper:
Sealing compound/
Verguss
Shell/
Gehäuse:
C
C
Sealing gasket
/
see table/
siehe Tabelle
Dichtung:
Sealing compound
/
Epoxy
Verguss:
Hexlocking screw
Sechskantschraube:
/
Stainless Steel/
Edelstahl
Installation specification/
Montagedaten:
Recommended torque
value/
empfohlenes Drehmoment:
3.1 in.LB / max. 6 in.LB/
35 Ncm / max. 67 Ncm
Recommended
panel cut-out/
empfohlener Montageausschnitt:
see sheet 2/
siehe Seite 2
Rear panel thickness/
Rückwand Dicke:
0.8 mm min. ... 1.3 mm max.
Hexlocking screw/
Sechskantschraube
B
B
Part no./
Part marked/ value/
Art.-Nr./
Capacitance
Quality
class/
Contact
plating/
Material
Sealing gasket/
Material
Kapazitätswert:
Gütestufe: Kontakt
Bedruckung:
Veredelung:
Dichtung:
Gold flash over nickel
15-009163
15-009161
15-009083
15-009081
15-009003
15-009001
15-009643
15-009641
15-009563
15-009561
15-009483
15-009481
3
1
3
1
3
1
3
1
3
1
3
1
Gold über Nickel
1200 pF
820 pF
370 pF
1200 pF
820 pF
370 pF
`
20 %
30 µin hard gold over min. 50 µin nickel
30 µin Gold über min. 50 µin Nickel
EMC gasket
Ni C filled/
EMV-Dichtung
Gold flash over nickel
Gold über Nickel
30 µin hard gold over min. 50 µin nickel
30 µin Gold über min. 50 µin Nickel
`
20 %
20 %
Nickel-Graphit gefüllt
Gold flash over nickel
Gold über Nickel
`
Sealing gasket/
Dichtung
30 µin hard gold over min. 50 µin nickel
30 µin Gold über min. 50 µin Nickel
Gold flash over nickel
Gold über Nickel
30 µin hard gold over min. 50 µin nickel
30 µin Gold über min. 50 µin Nickel
`
20 %
20 %
20 %
Gold flash over nickel
Gold über Nickel
30 µin hard gold over min. 50 µin nickel
30 µin Gold über min. 50 µin Nickel
Silicone gasket/
Silikon-Dichtung
`
`
Gold flash over nickel
Gold über Nickel
30 µin hard gold over min. 50 µin nickel
30 µin Gold über min. 50 µin Nickel
A
A
dim. in mm
IP67 D-SUB CONEC SlimCon Filter female 25pos. solder cup
with closed 4-40 UNC thread and hexlocking screw
Date/Datum
24.01.2018
24.01.2018
Name
Lehmenkühler
Fischer
IP67 D-SUB CONEC SlimCon Filter Buchsenleiste 25pol. Lötkelch
mit geschlossenem 4-40 UNC Gewinde und Sechskantschraube
drawn
/
gez.
appd./
gepr.
scale
/
Maßstab
:
Index: a Original
dwg no /
Z.-nr.:
DIN-
A3
R
15K1A2097
Status: InBearbeitung
3:1
1 / 2
RoHS compliant/konform
F
E
D
C
B
A